]> Basic Schema for IEEE 802.21 Information Service 1.0 A type identifier values for Information Elements. This property represents a bit number that has the value as true. 0x10000300 1 0x10000301 This class contains General Information depicting and Access Network Specific Information. 1 1 0x10000000 Link type of a network. The following values are assigned: 1: Wireless - GSM 2: Wireless - GPRS 3: Wireless - EDGE 15: Ethernet 18: Wireless - Other 19: Wireless - IEEE 802.11 22: Wireless - CDMA2000 23: Wireless - UMTS 24: Wireless - cdma-2000-HRPD 27: Wireless - IEEE 802.16 28: Wireless - IEEE 802.20 29: Wireless - IEEE 802.22 The range of #bit_number is 0-63. 0x10000001 1 1 The value is a non NULL terminated string whose length shall not exceed 253 octets. A value of Operator Type: 0: GSM/UMTS 1: CDMA 2: REALM 3: ITU-T/TSB 0x10000002 A non-NULL terminated string whose length shall not exceed 253 octets. 0x10000003 0x10000100 A non-NULL terminated string whose length shall not exceed 253 octets. 0x10000101 It is SSID if network type is IEEE 802.11. 0x10000102 0x10000103 1 1 1 The unit of the cost: 0: second 1: minute 2: hours 3: day 4: week 5: month 6: year 7: free 8: flat rate 9-255: Reserved The cost value in Currency/Unit A three-letter currency code(e.g. "USD") specified by ISO 4217. 0x10000105 1 1 A type to represent a class of service identifier. 0x10000106 0x10000107 0x10000108 0x10000109 The range of #bit_number is 0-31. 0x1000010A The range of #bit_number is 0-31. 0x1000010B 0x1000010C The range of #bit_number is 0-15. 0x1000010D 0x1000010E 0x1000010F 0x10000302 1 1 1 1 1 This class contains all the information depicting a PoA. 0x10000200 0x10000201 This class has properties that represent geographic coordinate. The format is based on the Location Configuration Information (LCI) defined in RFC 3825. Following codes are defined: 1: Meters: in 2s-complement fixed-point 22-bit integer part with 8-bit fraction. If AT = 1, an AltRes value 0.0 would indicate unknown altitude. The most precise Altitude would have an AltRes value of 30. Many values of AltRes would obscure any variation due to vertical datum differences. 2: Floors: in 2s-complement fixed-point 22-bit integer part with 8-bit fraction. AT = 2 for Floors enables representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. Altitude resolution. 6 bits indicating the number of valid bits in the altitude. Values above 30 (decimal) are undefined and reserved. Following codes are defined: 1: WGS 2: NAD 83 (with associated vertical datum for North American vertical datum for 1998) 3: NAD 83 (with associated vertical datum for Mean Lower Low Water (MLLW)) Geo address elements as described in RFC4119. This class has properties that represent civic address. The format is defined in IETF RFC 4676. Two-letter ISO 3166 country code in capital ASCII letters. This property contains the civic address elements. The format of the civic address elements is described in Section 3.4 of IETF RFC 4676 with a TLV pair (whereby the Type and Length fields are one octet long). 1 1 A one-octet descriptor of the data civic address value. The civic address value. Geo address elements as described in RFC4119. 0x10000202 1 1 Lowest channel frequency in MHz Highest channel frequency in MHz 0x10000203 0x10000204 1 1 The bit length of the prefix of the subnet to which subnet_address property belongs. The prefix_length is less than or equal to 32 for IPv4 subnet and less than or equal to 128 for IPv6 subnet. An IP address of the PoA encoded as Address base type defined in RFC3588. The first 2-octet contains AddressType, which may be either 1 (IPv4) or 2 (IPv6). If AddressType==1, the subnet_address property contains a 4-octet IPv4 address. If AddressType==2, the subnet_address property contains a 16-octet IPv6 address. 0x10000205 1 1 An Address Family defined in http://www.iana.org/assignments/address-family-numbers. An address value specific to address_type.